The TDUX system is a unique, inflatable, wraparound duct sealing product for permanently sealing telephone cable ducts in order to prevent the leakage of water from the duct into exchange vaults or manholes. The system can be installed even while water is flowing out of the duct, resulting in considerable time and cost savings.

• full product range for all duct diameters

• lifetime ± 20 years

• fast and easy to install and remove

• withstands 5 meters of waterhead and severe
  environments

An anodized coating that is color coded by size protects these couplers and connectors, increasing their durability in the field. Designed for all types of polyethylene ducts,
these products feature a ribbed external surface that provides excellent non-slip gripping during installation. Their low profile allows the couplers to pass easily through plowchutes.

• Easy to apply and remove
• Bonds to cable jacket
• Available with or without valve
• Four sizes cover cable diameters from .4 inches to 3.5 inches
• Bonds directly to the cable jacket eliminating the need for additional components
VAAC and FAAC self-adhering, heat-shrinkable cable end caps seal water out and seal pressure in on polyethylene jacketed cable, pipes and conduits. Systems approved, these highly reliable end caps are available with or without valves. They are used extensively by major
telephone companies and telephone cable manufacturers.

Tyco Electronics’ Biplex plugs seal 1 or 2
cables in a (nominal) 50mm O.D. (with
4.6mm wall) duct.

• All plastic construction-corrosion proof

• Water tight

• Simple to install

• Removable and reusable

• Chemically resistant

• No special tools required on installation

• Protects cable from sharp corners at the
  duct entry

Blank duct plugs effectively seal conduits to reduce the cost of cable placement and maintenance in new underground construction projects and routine work. These plugs are economical because they are removable
and reusable.

Duct Bank Durability:
Manufactured from high-impact plastic components, combined with durable elastic gaskets, Blank plugs are corrosion proof and effective as long-term or temporary seals.

Designed to adapt Tyco Electronics’ Simplex, Triplex or Quadplex plug’s hole sizes to different cable or subduct sealing ranges, Bushing Sleeve Adaptors allow installers to
customize our duct sealing product range to project-specific needs. When cables of different sizes occupy the same conduit, Bushing Sleeves, rather than expensive
custom plugs, solve the problem.

Valve-Equipped Entrance Seal for CEVs are built for use with Controlled Environment Vaults (CEVs). These fittings allow linemen the opportunity to check for water behind the seal prior to opening the conduit for work. Each
fitting includes a male-threaded nipple with integral pressure valve for the controlled drainage of water. Unlike competing products, these fittings accept standard conduit seals available from a variety of manufacturers.

Custom duct plugs can be designed to accommodate a specific customer requirement to effectively seal conduits, reducing the cost of cable placement and maintenance in underground construction projects and routine work. The custom size plugs feature a split design for sealing around, organizing, and supporting subducts, pipes, or cables.

Fiber Optic Simplex plugs effectively seal conduits containing one cable. Originally designed for applications involving fiber optic cable placement in subduct, this product is ideal for sealing around coax or twisted pair
cable in small diameter conduits. These plugs are retrofitable, removable, and reusable.

Designed to temporarily or permanently seal cable port or subduct openings in Simplex, Triplex and Quadplex sealing devices, hole plugs are made of solid polypropylene plastic and larger sizes feature pull tabs for easy removal.

Coupling polyethylene conduits or ducts by hand is a time consuming process that can cause wrist fatigue and inconsistencies in the quality of each duct joint completed. To reduce installation time, increase the level of quality, and provide greater consistency, hydraulic coupling presses are used. With duct counts per route increasing, presses are preferred by a growing number of installation
contractors.

MOON-Link duct couplings are constructed of a polyurethane elastomeric gasket within a durable, transparent outer shell. They are designed for coupling all types of conduit. The component parts are see-through, so the installer can verify that the conduit ends are fully seated within each half of the coupling.

The Minitube Sealing System offers a range of sealing plugs for sealing minitubes in duct networks Minitubes in duct networks entering subscriber premises and cabinets need to be protected to increase their service life by making sure the minitubes and ducts are clear and free of any water, sediment, or nesting animals.

Also known as Innerduct Pulling Eyes or Subduct Pulling Eyes, these heavy-duty products securely connect flexible conduit and HDPE duct to swivels and winch lines.
Pulling Eyes are designed for the wide variety of flex-, sub- and inner-ducts used in telecom and utility construction. They are manfactured of solid plated steel and withstand years of abuse in the field. Hex head design provides for easy installation.

Quadplex duct plugs are split plugs for sealing around, organizing, and supporting up to three subducts, pipes, or cables. These plugs are designed for use in round openings such as conduits, conduit fittings, and core-drilled wall penetrations. Effective, long-term watertight
and air-tight seals, prevent mud, backfill, and slurry from entering handholes, manholes, and buildings during the construction process.

Simplex entry seals effectively seal around and support conduits and cables in through-penetration openings or core drilled penetrations, such as building entrances or conduit openings. Simplex entry seals prevent leakage around conduits and cables entering structures of all kinds. Because of their split design, these plugs are retrofitable, removable, and reusable.

SPLIT-Link couplers are ideal for tie-downs, duct repair, and connections to high-pressure cable blowing equipment. Frequently required for cable placement, split couplings are designed to withstand over 200 psi and be
removable and reusable. SPLIT-Link couplers are designed for use with smooth walled and ribbed HDPE duct and innerduct.

Both water-tight and gas-tight, Tyco Electronics’ square duct plugs prevent the flow of water and the costly sedimentation of duct banks and conduit systems while
confining problems of dangerous vapors to their source. The service life of cable, splices, manhole hardware and electronics can be increased when contact with moisture
is reduced.

These female-to-male threaded connectors are designed to secure innerduct to cabinets and junction boxes. They consist of a universal threaded coupling end and a nipple end with locking washers and gaskets. The connectors
attach to standard knockout sizes in panels and racking for maximum security to premise cabling, eliminating cable kink at these transitions.

A. Fiber Optic Simplex Plug Installation Tool Designed to give the installer extra reach and facilitate the installation of Fiber Optic Simplex plugs, this tool opens up to wrap around cable and is made to grip the plug’s collar. The
knurled surface of the tool provides traction for tightening.

Fabricated of UV-stabilized Sch 80 PVC, transition couplings are specifically designed to provide excellent mechanical connections between HDPE and PVC conduit.

Triplex duct plugs are split plugs for sealing around, organizing, and supporting up to three subducts, pipes, or cables. The plugs are designed for use in round openings such as conduits, conduit fittings, and core-drilled wall
penetrations. Effective long-term watertight and airtight seals, these products also prevent mud, backfill, and slurry from entering handholes, manholes, and buildings during the construction process.

TUFF-Link couplers are non-metallic high-pressure rated airtight couplings for smooth walled and ribbed HDPE duct and inner duct.

The TUFF-Link plastic duct coupler is specifically designed for both press-on and thread-on airtight connections of HDPE duct. It provides a stealthy profile that will not snag on a plow chute. It features high tensile
strength plastic with exceptional resistance to side load pressure for maximum durability.

AMP-FIT mechanical tube fitting products are designed specifically for use on telephone air pressurization systems. They include complete lines of fittings for CA-3131 type feeder pipe, 3/8 (9.53) tubing, 5 and 10 port manifolds
with pre-assembled “F” and shutoff valves at each port. Installation is made possible without the need for solvents or special cleaning procedures in a matter of seconds by use of a manually operated hand tool.